This page has been robot translated, sorry for typos if any. Original content here.

How to make a tear gas on the basis of your technical means

How to make a tear gas on the basis of your technical means

 

The method of manufacturing tear gas is so simple that anyone can master it. I recall two main points of behavior: extreme attention and caution. You need to prepare a certain set of items of equipment, and chemical products can be bought at any entertainment store or local chemical dealer. If you do not have a gas mask, buy it at the nearest specialized store. Gas masks are sold at commercial points of the ground forces and the Navy at a price of $ 10. Below are the elements of equipment necessary for the production of tear gas.

  1. Ring metal stand.

  2. Alcohol burner.

  3. The flask (300 ml volume)

  4. Clamping bracket.

  5. Rubber stopper.

  6. Glass tube.

  7. Bracket.

  8. Rubber tube.

  9. Condenser.

10. Rubber tube.

11. Ring metal stand.

12. Bracket with two holders.

13. Rubber tube.

14. Rubber tube.

15. Glass tube.

16. Rubber stopper.

17. Glass collection.

18. Glass tube.

19. Rubber tube.

20. Glass tube.

21. Rubber tube.

22. Air separator.

23. Glass tube.

24. Rubber tube.

25. Glass tube.

26. The beaker (volume 300 ml).

Technology of production of tear gas:

  1. This work is carried out in the garage or outside the building, but not in the kitchen.

  2. Mix ten parts of glycerin with two parts of sodium bisulfate in a flask (M 3) and heat this mixture. Do not fill the flask with more than a third, as the mixture foam when heated. If it starts to foam, adjust the heat. 3. As soon as you see that no tear gas is formed, and that dense bunches begin to form in the bulb generator (T ^ 3) or a brown sediment is formed in the tube (TM 6), move aside the source of thermal energy, gas mask) - and remove the sediment in the flask. You can merge it into an external tap. But do not pour into the wash sink and toilet.

  4. Quickly turn off the glass collector (M 17) with the rubber stopper. It is here that tear gas accumulates.

  5. Do not try to produce more than three ounces of gas per cycle.

  6. Make sure all connections are tight.

The sequence of operations for installing a tear gas generator plant:

  1. Ring metal support stands (1 and 11) are installed on the working surface.

  2. Bracket with brackets (4 and 7) are located on the ring stand (1).

  3. The bracket with two holders is located on the ring stand (11).

  4. The bulb-generator (3) is fixed in the bracket (4).

  5. Two sections of the rubber tube (10 and 13) are connected to the condenser (9).

  6. The condenser (9) is fixed in the bracket (12).

  7. The section of the glass tube (6) is inserted into the rubber stopper (5).

  8. Glass tubes (15 and 18) are inserted into the rubber stopper (16).

  9. Glass tubes (20 and 23) are inserted into the rubber stopper (21).

10. The rubber stopper (5) is inserted into the neck of the bulb-generator (3).

11. The rubber stopper (16) is inserted into the neck of the glass collector (17).

12. The rubber stopper (21) is inserted into the neck of the air separator (22).

13. Connect the glass tube (6) to the condenser (9) and to the rubber tube (8).

14. Connect the condenser (9) to the glass tube (15) and to the rubber tube (14).

15. Connect the glass tube (18) to the glass tube (20) and to the rubber tube (19).

16. Connect the glass tube (23) to the glass tube (25) and to the rubber tube (24).

17. Connect the rubber tube (13) to the faucet. 18. Pull the end of the rubber tube (10) into the wash basin or into the drainage tank of the sewer system.

19. Fill the beaker (26) with water for three quarters of the volume and lower the glass tube (25) into the water.

20. Put the necessary ingredients in the flask-generator (3). 21. Open the water tap to supply water to the rubber tube (13).

22. Light the wick of the alcohol burner (2) and place it under the bulb generator (3).

The best method of preparing tear gas for practical use in operations is to pump it under pressure into glass vials or bottles. You can throw the bottle at any target you have set. From a collision with a solid surface, the glass container breaks, opening the outlet to tear gas. Other effective filling methods have also been tested, including compression compression in a nozzle, an aerosol dispenser, and even in bottles of seltzer water, and the like.