TYPICAL recorder failure "DAEWOO"

1). DAEWOO DV-F24D, DV-F44D, DV-F54D, and video recorder DAEWOO DVT2085D.

The first signs appear unreliable operation when you try to give the command to the remote to fast reverse (with a tap on the head). Mechanics enters certain averaged mode, gears are not included in the required grip. Clutch can crackle 'panes teeth. After the stop, and try again, can perform the desired, or may refuse to work, tinker with brute-force provisions. With time and the basic functions are not always followed. It comes to uncoordinated work of the brake levers and, as a result, loops with stop after rewinding, and gusts pozhёvannosti. Software wheel cleaning (round bracket) is desirable, because observed phones coming on sale !!! dirty (oxidized) software. Especially those suffering videodvoyki DAEWOO DVT2085D. And of course, to grease. But the problem could not be there. It is necessary to remove the broach. Remove mine ... in short reach gears - snails and remove it. For the shamans do not need to paint. Here are below it, and is the source of evil. This plate (arm) with riveted on her end of the sleeve, by which she "slips" on patterns of snails.

Steel is certainly shaky. And it certainly sleeve loose. Even a small gap leads to malfunction. Proklёpyvaem carefully. Control the sleeve perpendicular to the plate. We are trying to collect. All. It is advisable to brush up Engine Belts download. To put the size should be native. "At smaller than" here will not work - will not pull engine.

2). DAEWOO DV-K10W.

It does not turn on. The most common cause for this is the burned chip in BP - TOP214. Sometimes it explodes. It is advisable to check the well-being by her side elements for damage in the explosion. Very common. Reasons other than the skew rolls and the phase in the network is detected

3). DAEWOO DVR1989D.

Stops during PLAY. The reason - the failure of the opto-sensor rotation podmotochnogo node. You can look for. But it is difficult to reach. After 2 years of requests Koreans sent to the service center only 3 units. But you can do (such as temporarily) jumper at the control processor. With 7pin control processor (REEL) 5pin on his own (25 Hz half-frame), check the oscilloscope, I could take the memory, it is desirable to disable the sensor from proca by removing a jumper on the board. In videodvoyki DAEWOO DVT-2085D, DVT-2083D, respectively, the same 7 (reel) with 17 foot (drum fg) - there is a different firmware. The mechanics of this player quite robust, with take-up there were no problems. So the temporary becomes permanent

4). Videodvoyki DAEWOO DVT-2085, DVT-2083D.

It does not work, or the AV or TV. Very often burned resistor - fuse (gray) R817 (1 Ohm 1W), which stands in the chain of supply between + 14v 12 foot pulse tr-ra T801 connector and PV03, going to the VCR unit. And so, as the video is silent, then the I2C bus controller M37204-230SP does not give the command to switch TV. And again, immediately see whose is 7809? If the guess KIA- set out on the many secrets that have to do with it. Otherwise, you will pursue glitches broach.

5). DAEWOO DVR 1998D.

No color in PAL, SEKAM there are flashing horizontal lines if loss on the tape, the failure of the synchronization, although floor recording on another unit is played well. Guilty turned videoprots.LA7391.

6). DAEWOO F24 with a source of supply of SONY.

Poor start when connecting the cable to the network (squeaks, does not go into the operating mode), after starting work well. It is necessary to change the C53 1,0h100.

7). VIDEO RECORDER.

VCR I deliberately do not specify a brand unit because this defect can occur at any Vidak. The defect is as follows: When the tape to play a few times, you can see the following picture. The image on the television may be normal, it can be seen only half of the image, and can be anything at all invisible, one snow. The defect is in the motor camp cap, which moves the film. There is the capacity of one single electrolytic so she gives the defect. We need to change it.

8). Daewoo (model last 2-3 years).

Play mode turns off after a few seconds, and if the throw the cassette tape will hang from it. The problem is beam-damper. First plastic from which it is made is bent and he begins to not reach the feed and take-up reel. The output cut (near the axis of the lower side) plastic pimpochki (which ostensibly support it), and the second to disassemble itself damper cleaned with alcohol to display the previous effort.