TECHNOLOGY OF OIL AND PETROLEUM PRODUCTS CLEANING

TECHNOLOGY OF OIL AND PETROLEUM PRODUCTS CLEANING

Pashkin Mikhail Petrovich

In Russia, a unique, absolutely environmentally friendly, without the cost of electricity, a technology for cleaning oil and petroleum products from such harmful to oil and oil products components as chloride salts, aromatic resins, paraffins, water, sulfur.

I will not describe the processes associated with the current methods of cleaning oil and petroleum products from the above substances - specialists will immediately understand what is being said, I just want to note that it is thanks to these methods that the environment is mainly polluted, Expenses for processing and cleaning of oil and oil products.

The technology developed in Russia allows to save the processed product from most of the harmful components within 3-9 days. The truth is not yet developed the technology of simultaneous disposal of all harmful components, if the sulfur content in the product exceeds 1.5%.

How does this technology differ from all existing ones? But this is what.

Firstly , the more processed volume, the better the reaction takes, removing harmful components (VC).

Secondly , the treatment is carried out by a small part of the processed substance (OM). Those. We are provided with 5-10 liters of OM, for 1 hour we process it and give it back for pouring into the main tank. For an example - on 1t. OM need 10 liters. Of initial OM, 60 liters - 5 liters, but 1000 tons - 10 liters, for 50,000 tons - 40-50 liters.

Thus, the process of processing takes place in a container in which it is in the liquid state of the OM at any temperatures. And, if the volume "grabbed", then the process of improving the quality of OM will go also at sub-zero temperatures. We tested it at minus 18 degrees on oil, which freezes at plus 10 degrees (a lot of aromatics and paraffin). The volume was treated for 2 days at a temperature of plus 10-12 degrees, then it sharply cooled to minus 18 degrees, but oil containing up to 24% of "bound" water, 68000 mg / l of chloride salts, having a density of 0.923 at 20 degrees and 0.925 at 15 Degrees after 3 days has become another. A third of the volume (from above) has the following properties: water - 0.1%, chloride salts - 254 mg / l, density - 0.857. The process of improvement continued further, but we could not get the final results for purely technical reasons (in our country so often happens).

What is fixed on the so-called. "Trap" oil. Its initial parameters were as follows:

  • Density - 1044 kg / m3;
  • Water-cut,% of mass. - 75;
  • The content of salts, mg / dm3 - 102825;
  • Sulfur content,% wt. - more than 3,5;

When heated, it decomposes.

But what happened after the 3-day "standing" in the tank, after processing:

According to the analysis taken at the top of the tank: sulfur - 4.06%, chloride salts - 370 mg / dm3, water - is absent.

According to the analysis taken after mixing the tanks: sulfur - 4.6%, chloride salts - 700 mg / dm3, water - 5.2%.

From the same stirred tank oil was sent for analysis of the fractional composition.

Here's what happened:

Volumetric fraction of evaporated fraction%

  • At 200 degrees - 10;
  • At 300 degrees - 26;
  • At 350 degrees - 48;
  • At 360 degrees - 58.

The boiling point is 69 degrees, sulfur is 4.19 percent.

There are small discrepancies in sulfur, but the analyzes were done in different certified laboratories.

What surprised us the most in this matter was that the volume of processed oil did not change! Those. About 70 percent of the water turned into oil! We wanted to reduce the sulfur content, but it turned out that the water got bad, but oil. It can already be improved further, focusing only on sulfur, but we have not done so yet.

When we removed sulfur, aromatics from light oils, without water, sulfur and aromatics practically did not become. And from diesel, d / t sulfur with 1% drops to 0.02%.

Many of their acting doctors and academicians are aware of these works, but do not recognize them, because It does not fit into their ideas about science, and they say that these are all the doctors, but we began to ignore such "scientists" - we do not address them any more. There are many other, normal business people who are already convinced of the superiority of our technology and offered cooperation.

On behalf of those who invented this technology
Pashkin Mikhail Petrovich.
Chairman of the Coordinating Council of the Trade Union of Police Officers in Moscow.
Http://www.prof-police.ru/
T. 495 699-88-91

print version
Author: Pashkin Mikhail Petrovich
PS The material is protected.
Date of publication 03.02.2007gg